Handbrake reduce file size7/4/2023 ![]() Wpp / ctu=64 / min-cu-size=8 / max-tu-size=32 / tu-intra-depth=1 / tu-inter-depth=1 / me=1 / subme=2 / merange=57 / no-rect / no-amp / max-merge=2 / temporal-mvp / no-early-skip / rdpenalty=0 / no-tskip / no-tskip-fast / strong-intra-smoothing / no-lossless / no-cu-lossless / no-constrained-intra / no-fast-intra / open-gop / no-temporal-layers / interlace=0 / keyint=250 / min-keyint=23 / scenecut=40 / rc-lookahead=20 / lookahead-slices=5 / bframes=8 / bframe-bias=0 / b-adapt=2 / ref=3 / limit-refs=3 / no-limit-modes / weightp / no-weightb / aq-mode=3 / qg-size=32 / aq-strength=1.00 / cbqpoffs=0 / crqpoffs=0 / rd=3 / psy-rd=2.00 / rdoq-level=0 / psy-rdoq=0.00 / no-rd-refine / signhide / deblock=0:0 / sao / no-sao-non-deblock / b-pyramid / cutree / no-intra-refresh / rc=2 /qcomp=0.60 / qpmin=0 / qpmax=51 / qpstep=4 / cplxblur=10.0 / qblur=0.5 / ipratio=1. Video Settings H.265 (10-bit), Framerate: same as source VBR, Target Size (235MB for 1-hour shows, 120MB for 30-minute shows), 2-pass encoding and Turbo first pass checked Encoder setting set to slow and Profile: Level 4.1 Audio Settings Codec: AAC, Mixdown: Stereo, Bitrate: 64kbps, Gain: 3įor Movies and Tv Shows, I use these settings under More Settings options: You can get good results with 1500kbps if you want smaller file sizes, but 2K is where I find it works to my liking.įor TV Shows I do everything in 720p/480p based on source. Typical results: 90 minute movies come out to about 1.5GB, 105 minute movies around 1.75GB, and so on based on length of film. Video Settings H.265 10-bit, Framerate: Same as Source VBR, Average Birtrate (2000) 2-pass encoding and Turbo first pass checked Encoder Setting set to slow and Profile: Level 4.1 Audio Settings: Codec: E-AC3, Mixdown: 5.1 channels, Bitrate: 224kbps, Gain: 3 however, sometimes faint things like a cloud in the upper right corner has blurry edges after i reencode.It won't let me post a screenshot, but here are the settings I use:įor movies I do everything in 1080p. the movie is not ruined if i reencode the 1150 kbps movie. i read that the loss in quality caused by turbo first pass is not noticeable. You should not expect an x264 encode at RF 25 to be similar to. Even where the quality scale is similarly labeled, quality values are not comparable between encodes across multiple encoders. you can use constant quality if you are focusing on the quality and not file size. In all cases, adjusting HandBrake’s quality control to the right always increases quality, and adjusting the control to the left always decreases quality. i will be ruining the movie if i reencode the 1150 kbps movie and the original high resolution movie needs to be reencoded.constant quality is better than two pass encoding.people told me that what i am doing is wrong because:. ![]() I did some inquiries to see if what i am doing is ok. i encoded a bunch of movies at 900 kbps using these settings and the movies looked ok my settings in handbrake are 720p, x264 mp4, slow preset, turbo first pass encoding, two pass encoding, constant frame rate, same frame rate as source and audio 128 kbps aac. mp4 movies which have video bitrate which is either 800 kbps or 850 kbps or 900 kbps. i wasted a lot of time reencoding the movies and trying different crf values it didn't work out that well and sometimes the file size didn't shrink and sometimes it shrunk by a lot and the movie quality was ruined in some parts of the movie and pixels showed. Once the file is loaded, you can choose where to save it simply by clicking Browse. In the beginning i tried using constant quality. Then you can choose the file you want to compress and click Open. ![]() mp4 movies that i download from that website are ripped at video bitrate 1150 kbps and the file sizes are bigger so i want to reencode the movie that i download by using handbrake to shrink the file size mp4 movies that i downloaded from a website were ripped at around video bitrate 850 kbps and the file sizes were between 700mb and 900mb.
0 Comments
Leave a Reply. |